Introduction to parasitic inductors - 응용 프로그램 | Heisener Electronics
고객 문의
SalesDept@heisener.com +86-755-83210559 ext. 813
Language Translation

* Please refer to the English Version as our Official Version.

Introduction to parasitic inductors

에 게시 12월 6, 2022

I do not know when you debug the circuit, have encountered this situation, that is, all the components on the board parameters and welding are correct, but after the power, some components in the circuit immediately damaged. This phenomenon probably has something to do with a hidden object in the circuit - parasitic inductance.

As the name suggests, parasitic inductance refers to the inductance parasitic on the PCB wiring or other components of the circuit board. Generally speaking, there will be a parasitic inductance where there is a wire, such as the copper wire on PCB, through the hole, even the bonding wire inside the chip will have a certain amount of parasitic inductance, the inductance of these parasitic inductors is generally from a few nH to dozens of nH.

● LP6451 synchronous Buck circuit is used to introduce the influence of parasitic inductance on the circuit.

Figure 1 is the typical application schematic diagram of LP6451, LP6451 uses COT control architecture, support the maximum 18V DC input, can provide the maximum 3A load current, at the same time LP6451 also integrated input undervoltage protection, output short-circuit protection, overcurrent protection, overtemperature protection and other functions, with excellent electrical performance, good safety and other advantages, Is a very cost-effective synchronous buck control chip.

       

                                                            Figure 1: Schematic diagram of typical application of LP6451


Effect of parasitic inductance on input.

At the input end of LP6451 scheme, two ceramic capacitors C2 and C3 will be placed to filter the input voltage and stabilize the input voltage. On the PCB board, the two ends of the circuit from the input end to the capacitors C2 and C3 are connected by the PCB wiring, which is actually the existence of parasitic inductance. We use the simulation software to see what changes will occur at the input end when the circuit is on after the introduction of 20nH parasitic inductance L1.

As can be seen from the simulation results in Figure 2, when the blue input voltage increases from 0V to 12V, the voltage on capacitor C1 does not rise to a stable 12V, but becomes an oscillating sine wave, and the peak voltage of the sine wave reaches 24V, which is twice the input voltage of 12V. If this voltage exceeds the maximum voltage tolerance of the components in the circuit, it will cause them to fail.

    

                                                                                                  Figure 2: Simulation results


At this point, many engineers may ask, why do we not always see this oscillation in the input capacitance in practical applications? This is because in addition to the introduction of parasitic inductance, the PCB wire also introduces an additional resistance, and this resistance acts as a damping damping effect on the sinusoidal oscillation. On the basis of the previous simulation circuit, we added resistor R1. It can be seen that with the increase of resistor R1 resistance, the voltage attenuation rate on the input capacitor becomes faster and the maximum voltage also decreases rapidly.

        

                                                                                       Figure 3: New simulation results


Although the voltage oscillation caused by the parasitic inductance at the input end can be alleviated by the parasitic resistance at the same time, we should always pay attention to the voltage waveform on the input capacitor at the moment of power-on when designing the power supply, so as to avoid abnormal high voltage and damage to the circuit elements behind the input capacitor.

주요 구성 요소

부품 번호 설명
LPC54S016JET100E
NXP
내장형 - 마이크로 컨트롤러, IC MCU 32BIT ROMLESS RFQ
LPC55S69JBD100K
NXP
내장형 - 마이크로 컨트롤러, IC MCU 100MHZ CORTEX M33 DUAL RFQ
LPC55S66JBD100K
NXP
내장형 - 마이크로 컨트롤러, IC MCU 100MHZ CORTEX M33 320KB RFQ
LPC55S69JEV98K
NXP
내장형 - 마이크로 컨트롤러, IC MCU 100MHZ CORTEX M33 DUAL RFQ
LPC55S66JEV98K
NXP
내장형 - 마이크로 컨트롤러, IC MCU 100MHZ CORTEX M33 320KB RFQ

Related Articles

  • How to maximize the efficiency of SiC traction inverter by real-time variable grid drive strength?

    Traction inverters are the main battery drain components in electric vehicles (EVs), with power levels up to 150kW or higher. The efficiency and performance of traction inverter directly affect the driving range of electric vehicle after a single charge. Therefore, in order to build the next generation of traction inverter systems, silicon carbide (SiC) field effect transistor (FET) is widely used in the industry to achieve higher reliability, efficiency and power density.

  • Do you know the 8 application circuits of operational amplifiers?

    Do you know the 8 application circuits of operational amplifiers?

  • How do you configure an op-amp in a typical gain control circuit?

    This technical presentation requires an understanding of how to configure an operational amplifier in a typical gain control circuit. The applications of linear and nonlinear digital potentiometers are discussed. This article gives an overview of the basic techniques required to convert audio and other potentiometer/op amp applications from conventional mechanical potentiometers to solid state potentiometers

  • Simple way to limit current using integrated MOSFeTs

    The current in an electronic circuit usually has to be limited. In USB ports, for example, excessive current must be prevented to provide reliable protection for the circuit. Also in the power bank, the battery must be prevented from discharging. Too high discharge current results in too large voltage drop of the battery and insufficient supply voltage of downstream devices

  • Three excellent ways to reduce audible noise in motion control applications

    Using advanced real-time control technologies such as motor control circuits with higher power density, higher integration and more efficient systems, better acoustic performance of the system can be achieved

  • How to control brushless DC motor?

    Brushless direct current (BLDC) motors have been widely used in household appliances, industrial equipment and automobiles. While brushless DC motors offer a more reliable and maintainable alternative to traditional brushless motors, they require more sophisticated electronics to drive them

  • How to achieve precise motion control in industrial actuators

    How to achieve precise motion control in industrial actuators

  • Summary of PCB design strategy for GaN drivers

    The NCP51820 is a 650 V, high-speed, half-bridge driver capable of driving gallium nitride (" GaN ") power switches at dV/dt rates up to 200 V/ns. The full performance advantages of high voltage, high frequency and fast dV/dt edge rate switches can only be realized if the printed circuit board (PCB) can be properly designed to support this power switch. This paper will briefly introduce NCP51820 and the key points of PCB design of high performance GaN half bridge grid driver circuit using NCP51820